I think it would therefore be much appreciated if everyone could submit new PRs with “friendly name” as a description if you got any ZHA compatible Zigbee USB adapters which unique Vendor ID (vid) / Product ID (pid) identifier that has not yet been a… https://resources.pcb.cadence.com/blog/2020-understanding-ceramic-chip-antenna-vs-pcb-trace-antenna

SONOFF Zigbee 3.0 USB Dongle Plus V2 (first need to run update script if from first hardware batch shipped) Perhaps more important to know today is that EZSP v5, v6 and v7 (EmberZNet 6.6.x.x) use the same framing format, but EmberZNet 6.7.x.x/EZSP v8 introduced new framing format and expanded command id field from 8 bits to 16 bits." sysctl "net.ipv6.conf.all.disable_ipv6=0 net.ipv4.conf.all.forwarding=1 net.ipv6.conf.all.forwarding=1" \ Silicon Labs Simplicity Studio included "Flash Programmer" ( instructions) (can't find your device? read below!)They have posted a video on ITead’s Facebook group for Sonoff showing this new dongle working out-of-the-box with the ZHA integration for Home Assistant (via the bellows radio library for its zigpy dependecy): They now posted some documentation which states that this hardware dongle does support “Hardware Flow Control” but default firmware that it is flashed does not (so default uses “Software Flow Contol”): Important: The IAR Embedded Workbench for ARM (IAR EWARM) Compiler is currently not supported with OpenThread. Debug 2022-08-31 08:16:43Received Zigbee message from '0x00158d000894fa97', type 'attributeReport', cluster 'genBasic', data '{"65281":{"1":3055,"10":0,"100":0,"11":142,"3":24,"4":424,"5":62,"6":[0,0]}}' from endpoint 1 with groupID 0 This is one of the main reasons why you want to do everything you can to avoid any source of interference, but it is also why you want to have many Zigbee Router devices in your Zigbee network mesh so that devices that are far away from the Zigbee Coordinator will connect through a Zigbee router instead of directly to the Zigbee Coordinator.

In addition, ITead specifically mentions that this TI dongle can alternatively function as a Zigbee router (presumably by flashing Zigbee router firmware instead and open access buttons as pressing a button to enable pairing/joining mode is usually required). Wondering if this CC2652P serial port will have pins connected for RTS / CTS Hardware Flow Control? ZB-GW02 (SM-011 V1.0 module-based) gateway looks to be Tuya type WiFi gateway with "SM-011 V1.0" module pre-soldered.Manual Xmodem sending commands over a terminal console (note that any terminal application with "Xmodem(N)" send can be used) https://github.com/xsp1989/zigbeeFirmware/blob/4533c8daa1e571801a2c49dca8498a1b1b79f54f/firmware/Zigbee3.0_Dongle/EZSP/README.md Update! Broken down the steps to flash firmware mentioned from https://github.com/JelmerT/cc2538-bsl/pull/114 into a basic guide for flashing ITead SONOFF Zigbee 3.0 USB Dongle Plus adapter. Stop any applications or services that might be connected to the Zigbee adapter via serial port (ex. Home Assistant’s ZHA integration, Zigbee2MQTT, ioBroker, Jeedom, etc.). In my case, I ran the update on another computer so nothing to stop there.

First, you have to disassemble the device and pull the logic board out of its housing. You need a J00 Phillips screwdriver for this.Debug 2022-08-31 08:20:29Received Zigbee message from '0x00158d000894fa97', type 'attributeReport', cluster 'genBasic', data '{"appVersion":5,"modelId":"lumi.sensor_motion.aq2"}' from endpoint 1 with groupID 0 Should be noted that a few manufacturer's devices (most notably a few Aqara/Xiaomi and Tuya devices) have badly written firmware that either prevents them from routing messages from other manufacturer's brands of devices or refuses to connect through a Zigbee Router that is not of the same manufacturer and/or brand. Please help improve/enhance all of the integration documentation after you tested the dongle and ZHA: https://github.com/zigpy/zigpy/wiki/Generic-best-practice-tips-on-improving-Zigbee-network-range-and-general-stability

Also, I can personally recommend using a few of their USB adapters flashed as Zigbee Routers too. UPDATES AND TIPS! Tuya ZS3L module has a circuit board antenna while the smaller Tuya ZSLC5 have fewer IO pins and does not have an antenna so needs an external antenna via pin 1. FYI, Home Assistant can already detect a few different Zigbee USB radio adapters, including the CC2652P-based Sonoff ZBDongle-P USB dongle from ITead, and it now looks like Home Assistant will soon support also be able to automatically do USB discovery for this new [ITead’s “Sonoff Zigbee 3.0 USB Dongle Plus V2” model “ZBDongle-E” based on Silicon Labs EFR32MG21, at least if they merge:Run command to flash from command-promt (cmd.exe) launched as elevated Administrator, example with firmware release available at this time: python cc2538-bsl.py -p COM5 -e -v -w --bootloader-sonoff-usb CC1352P2_CC2652P_launchpad_coordinator_20211217.hex BRD4001A: Wireless starter main boards (WSTK) to host the radio boards. Except for BRD4166A, all the radio boards need a starter main board each. Mini USB cables to connect and power the main boards or micro USB cable for BRD4166A. Also, I can personally recommend using a few of their USB adapters flashed as Zigbee Routers too. Zigbee 3.0 USB Dongle Plus - ZBDongle-E variant While the Zigbee specification supports changing channeI on an existing Zigbee network I do not think that ZHA support that feature yet? See → https://www.home-assistant.io/integrations/zha/#defining-zigbee-channel-to-use